世の中に去年の自分より今年の自分が優れていないのは立派な恥です。それで、人材として毎日自分を充実して、IBM SurePOS 500 Models 5x5 Technical Mastery問題集を学ぶ必要があります。弊社のIBM SurePOS 500 Models 5x5 Technical Mastery問題集はあなたにこのチャンスを全面的に与えられます。あなたは自分の望ましいIBM SurePOS 500 Models 5x5 Technical Mastery問題集を選らんで、学びから更なる成長を求められます。心はもはや空しくなく、生活を美しくなります。
CertJukenはいつまでもお客様の需要を重点に置いて、他のサイトに比べより完備のIBM SurePOS 500 Models 5x5 Technical Mastery試験資料を提供し、IBM SurePOS 500 Models 5x5 Technical Mastery試験に参加する人々の通過率を保障できます。お客様に高質のIBM SurePOS 500 Models 5x5 Technical Mastery練習問題を入手させるには、我々は常に真題の質を改善し足り、最新の試験に応じて真題をアープデートしたいしています。我々IBM SurePOS 500 Models 5x5 Technical Mastery試験真題を暗記すれば、あなたはこの試験にパースすることができます。
IBM SurePOS 500 Models 5x5 Technical Mastery練習問題は、若干の質問と回答のサンプルを提供します。 あなたは私たちのIBM SurePOS 500 Models 5x5 Technical Mastery試験関連資料の無料のデモを試してみて、それをダウンロードすることができます。満足している場合は、ショッピングカートに追加することができます。気に入らば、ショッピングカードにIBM SurePOS 500 Models 5x5 Technical Masteryトレーニング資料を入れます。支払いをした後、こちらはあなたのメールボックスにIBM SurePOS 500 Models 5x5 Technical Mastery練習問題を送ります。そして、あなたは電子メールをチェックして、添付ファイルをダウンロードできます。
P6040-014試験問題集をすぐにダウンロード:成功に支払ってから、我々のシステムは自動的にメールであなたの購入した商品をあなたのメールアドレスにお送りいたします。(12時間以内で届かないなら、我々を連絡してください。Note:ゴミ箱の検査を忘れないでください。)
IBM P6040-014 試験シラバストピック:
| セクション | 目標 |
|---|---|
| トピック 1: 設定と保守管理 | - 予防保守と診断作業 - ハードウェアの設定とBIOSの設定項目 |
| トピック 2: ソフトウェアと動作環境 | - 対応オペレーティングシステムおよびPOSソフトウェアとの連携 - ドライバーとファームウェアの管理 |
| トピック 3: IBM SurePOS 500 システムの概要 | - ハードウェアのアーキテクチャと構成要素 - システムのモデルと構成(5x5シリーズ) |
| トピック 4: インストールと導入 | - 物理的な設置と周辺機器の接続 - システムの起動と初期設定 |
| トピック 5: トラブルシューティングとサポート | - 一般的なハードウェアおよびシステムの障害 - 診断ツールと修理手順 |
IBM SurePOS 500 Models 5x5 Technical Mastery 認定 P6040-014 試験問題:
1. Which operating system is NOT supported on the IBM SurePOS 5x5?
A) IBM 4690 Operating System
B) Microsoft Windows XP Professional
C) Microsoft Windows 2000
D) IBM PC DOS 2000
E) Microsoft Windows Embedded for Point of Service
2. What is the starting point for diagnosing a problematic IBM SurePOS 5x5?
A) refer to the start up sequence listed in the User's Guide; power on and note any differences
B) attach a USBCD drive containing the IBM Diagnostics for POS Systems and Peripherals; power on the system; follow any corrective action
C) power on the system; pay particular attention to POST; make sure to observe the LED blinking and one beep before the system powers up
D) with the system off, reseat the DIMMs; power on thesystem
3. How is the Power up on LAN feature enabled?
A) by installing Power up on LAN from the Diagnostics Program
B) through Remote Management Agent
C) by installing the Power up on LAN driver from the Retail Store Solutions Web site
D) through the CMOS Setup Utility program
4. Where is the hard disk drivelocated in the IBM SurePOS 5x5?
A) at the rear of the system, just above the power supply
B) in the center of the system, underneath the center tower cover
C) at the rear of the system, behind the I/O tailgate cover
D) at the front of the system, directlyunderneath the front cover
5. Which statement is true about the order of steps for installing a magnetic stripe reader (MSR)?
A) 1. with a screwdriver, pop out the MSR hole plugs on the right side of the display
2.align the MSR tabs into the holes and slide down so that the MSR is flush against the display
3.remove the tower center cover to access the MSR connector 4.route the MSR cable in the groove on the back of the display and attach it to the connector in the center of the system
B) 1. with a screwdriver, pop out the MSR hole plugs on the right side of the display
2.align the MSR tabs into the holes and slide down so that the MSR is flush against the display
3.route theMSR cable in the groove and attach it to the back side of the display
4.at the back of the MSR device, tighten the thumbscrew to secure it to the display
C) 1. with a screwdriver, pop out the MSR hole plugs on the left side of the display
2.align theMSR tabs into the holes and slide down so that the MSR is flush against the display
3.route the MSR cable in the groove and attach it to the port on the rear connector panel
4.at the back of the MSR device, tighten the thumbscrew to secure it to the display
D) 1. open the bezel and remove the MSR plugs
2.with the bezel open, position the MSR tabs in the holes
3.connect the MSR cable to the connector on the operator card
4.close and secure the bezel
質問と回答:
| 質問 # 1 正解: A | 質問 # 2 正解: C | 質問 # 3 正解: D | 質問 # 4 正解: D | 質問 # 5 正解: B |




Mitsui
重泉**
Nakanishi
山吹**
